Sunburst baby quilt details - Part 2

If you're just joining me for the Sunburst baby quilt tutorial, see Part 1 here.

Part 2 starts now! We're ready to start piecing the circles. Layer a background wedge with a colored wedge...

right sides together, and sew a 1/4" seam starting at the wide top edge and ending at the skinny bottom edge.

Press your seam toward the colored wedge...

and make 11 more units just like this, always sewing from the wide top edge to the skinny bottom edge.

Then sew your twelve sections of two wedges into six sections of four wedges, remembering to sew from wide edge to skinny edge and press toward the colored wedge...

then sew your six sections of four into three sections of eight wedges. Press all the seams toward the colored wedges.

Sew the final three seams making a complete circle...

Now I'm giving you the opportunity to take a little detour because Geta Grama has the original tutorial with great photos and directions on how to cut your completed circle into an octagon here. I used her instructions when I made my blocks. I also took photos of each step of the process when making my blocks, so hopefully between the two of us, you'll be an expert at it! Come right back here after viewing her instructions, and you can read through mine too.

Now let's make this circle into an octagon. Cut a straight edge across three of the wedges...

Flip the unit upside down and cut the opposite edge, again cutting across three wedges...

Cut the remaining sides (at 3:00 and 9:00 on a clock) until your circle looks like this...

Now cut the remaining four curved edges, again cutting across three wedges each time...

And now you've got an octagon! Apologies here; I forgot to snap a photo of this :(

Cut each of your (24) 4.75" background squares diagonally corner to corner...

You're going to sew these triangles to four of the sides of your octagon as shown here. The placement of your triangles is very important! For each octagon with the colored fabrics in the center, place a background wedge at 12 o'clock. For the octagons with colored fabrics on the outer edges, a colored wedge will be at 12 o'clock. Very important for final construction!!

Align the outer point of each triangle with the center of each wedge for correct placement, and then sew a 1/4" seam on all four corners...

Press the seams toward the triangle. The triangles are cut a little too large so they can be trimmed down to the correct size making a perfect square. Align the top and right cut edges with the edges of a large square ruler...

And trim the corner triangle units to make your square edge. Repeat at each corner...

Now you should have a 12.75" square block!

Trace a circle large enough to cover the center opening (mine are a little less than 2.5" diameter) on to the paper side of some fusible web - I use Heat n Bond Lite. I used an unopened roll of lint roller refills as my template - hey, whatever works, right? Fuse the traced circle to the wrong side of your center circle fabric, and then cut out the circle...

Remove the paper backing from the fusible web, fuse the circle to your block, then blanket stitch around the circle...

Stand back and admire your fabulous "Dresden Circle made into an Octagon made into a Square"!!

Make the remaining 11 blocks and sew them into your quilt top!

One more important point. Notice in the quilt top how blocks with colored fabrics in the center are alternated with blocks where the colored fabrics are on the outer edges? And remember when I said you need to be careful about your placement of the corner triangles on each type of block?? Here's why. In order to give the Sunburst "circles" the appearance of floating and spinning, you want the colored wedges of each Sunburst to align with the background wedges of adjacent circles. That's why your corner triangle placement is key.

It also makes piecing the blocks so much easier since your seam allowances are pressed so that they will lay on either side when seamed!

Lastly, add the 2" cut border strips to each side of your quilt. You'll have to join three of the strips for enough length to be able to cut the borders for the two long sides of the quilt top. Add the long sides first, pressing the seams toward the border, then finally add the top and bottom borders. Voila - quilt top complete!!

Let me know if you have any questions about these directions. And I'd love to hear from you if you make one of these Sunburst quilts :) Send me a photo!

Now I'm off to decide on a quilting pattern for this baby quilt.

Thank you all so much for the wonderful response you've given to this quilt. It truly makes my day every time someone takes a few moments and leaves a comment :)